Ads Security FA700KP-ADS Guide d'installation télécharger pdf (Page 4)

– 4 –

✱

41 PRIMARY PHONE No.

| | | | | | | | | | | | | | | | | | |

✱

42 SECOND PHONE No.

| | | | | | | | | | | | | | | | | | |

Enter up to 20 digits. To clear entries, press

✱

✱ respectively

NOTE: Entry of a number other than one specified will give unpredictable results.

For fields *43 thru *46: Enter 0–9; #+11 for B; #+12 for C;

#+13 for D; #+14 for E; #+15 for F. Enter [

✱

]

as the fourth digit if a 3-digit account number (for 3+1 dialer reporting format) is used. Enter 0 as the first digit of a 4-

digit account number for Nos. 0000-0999. Exit field by pressing

✱

if only 3 digits are used. E.g., For Acct. B234, enter #+11-2-3-4.

✱

43 PARTITION 1 PRIMARY ACCT. No.

| | | / | | | | |

Enter 4 or 10 digits, depending on selection in *48 Report

Format. See box above. To clear, press

[FFFFFFFFFF]

✱

44 PART. 1 SECONDARY ACCT. No.

| | | / | | | | |

Enter 4 or 10 digits, depending on selection in *48 Report

Format. See box above. To clear, press

. [FFFFFFFFFF]

✱

45 PARTITION 2 PRIMARY ACCT. No.

| | | / | | | | |

Enter 4 or 10 digits, depending on selection in *48 Report

Format. See box above. To clear, press

. [FFFFFFFFFF]

✱

46 PARTITION 2 SECONDARY ACCT.

No.

| | | / | | | | |

Enter 4 or 10 digits, depending on selection in *48 Report

Format. See box above. To clear, press

. [FFFFFFFFFF]

✱

47 PHONE SYSTEM SELECT

[1]

If Cent. Sta.

IS NOT

on a WATS line: 0=Pulse; 1=Tone;

if Cent. Sta.

a WATS line: 2 = Pulse; 3 = Tone

✱

48 REPORT FORMAT

[77]

primary secondary

0 = 3+1, 4+1 ADEMCO L/S STANDARD

1 = 3+1, 4+1 RADIONICS STANDARD

2 = 4+2 ADEMCO L/S STANDARD

3 = 4+2 RADIONICS STANDARD

5 = 10-digit ADEMCO CONTACT ID® REPORTING

6 = 4+2 ADEMCO EXPRESS

7 = 4-digit ADEMCO CONTACT ID® REPORTING

8 = 3+1, 4+1 ADEMCO L/S EXPANDED

9 = 3+1, 4+1 RADIONICS EXPANDED

✱

49 SPLIT/DUAL REPORTING

[0]

0 = Standard/backup reporting only (all to primary)

Primary Phone No. 2nd Phone No.

1 = Alarms, Restore, Cancel Others

2 = All except Open/Close, Test Open/Close, Test

3 = Alarms, Restore, Cancel All

4 = All except Open/Close, Test All

5 = All All

✱

50 BURGLARY DIALER DELAY

[2,0]

Delay Time SIA-Comp. Controls

Delay Disable

Delay Time:

0 = no delay UL: must be “0”

1 = 15 seconds; 2 = 30 seconds; 3 = 45 seconds

SIA Guidelines: delay must be minimum of 30 seconds

SIA-Compliant Controls:

Delay Time: 1 = 15 seconds; 2 = 30 seconds; 3 = 45 seconds

Delay Disable:

0 = use delay set in entry 1

1 = dial delay disabled for zones listed in zone list 6 (use zone list

6 to enter those zones that require dial delay to be disabled;

these zones ignore the setting in entry 1)

UL: Dial delay plus entry delay must not exceed one minute; use

zone list 6 to disable dial delay from appropriate zones, if necessary.

✱

53 SESCOA/RADIONICS SELECT

[0]

0 = Radionics (0-9, B-F)

1 = SESCOA (0-9 reporting); Use “0” for all other formats.

✱

54 DYNAMIC SIGNALING DELAY

[0]

Select delay from 0 to 225 secs, in 15-sec increments.

0 = no delay (both signals sent), 1 = 15 secs,

2 = 30 secs, etc.

UL: Grade AA must be “0;” Grade A must be “15” max

✱

55 DYNAMIC SIGNALING PRIORITY

[0]

0 = Primary Dialer first; 1 = Long Range Radio first.

For UL Commercial Burglary installations that use a DACT

and LRR, this field must be “0”.

✱

56, *57, *58 MENU MODES

These are Menu Mode commands, not data fields, for Zone Programming, Function Key

Programming, and Expert Mode Zone Programming respectively. See page 2 and their

respective sections in the Installation and Setup Guide for procedures.

TO PROGRAM SYSTEM STATUS, & RESTORE REPORT CODES (

✱

59 thru *68, *70 thru

✱

76, and

✱

89):

For 3+1 or 4+1 Standard Format: Enter a code in the

first

box: 1–9, #+10 for 0, #+11 for B, #+12 for C, #+13 for D, #+14 for E, #+15 for F.

A 0 (

not

#+10) in the

first

box will disable a report. A 0 (

not

#+10) in the

second

box will result in automatic advance to the next field.

For Expanded or 4+2 Format: Enter codes in

both

boxes (1st and 2nd digits) for 1–9, 0, or B–F, as described above.

A 0 (

not

#+10) in the

second

box will eliminate the expanded message for that report. A 0 (

not

#+10) in

both

boxes will disable the report.

For Ademco Contact ID® Reporting: Enter any digit (other than 0) in the

first

box, to enable zone to report (entries in the

second

boxes are ignored).

A 0 (

not

#+10) in the

first

box disables the report. UL: see installation instructions for requirements

SYSTEM STATUS REPORT CODES (

✱

59–

✱

68)

✱

59 EXIT ERROR REPORT CODE

[0] See box above. SIA-Compliant Controls: [1] Always enabled.

✱

60 TROUBLE REPORT CODE

| [00] See box above.

✱

61 BYPASS REPORT CODE

| [00] See box above.

1 2 3 4 5 6 7 8 9 ... 15 16

Commentaires sur ces manuels

Pas de commentaire

Ads Security FA700KP-ADS Guide d'installation Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Ads Security FA700KP-ADS