Ads Security FA700KP-ADS Guide d'installation télécharger pdf (Page 3)

– 3 –

PROGRAMMING FORM

Entries apply to the FA168CPS/FA168CPSSIA and

FA148CP/FA148CPSIA

controls, except entries shown in dashed boxes, which apply

only to

the FA168CPS

/FA168CPSSIA

(partition entries) and are not applicable to the FA148CP/FA148CPSIA controls

SIA-Compliant Controls: Where noted, certain fields have special settings when used with the FA168CPSSIA and FA148CPSIA SIA-Compliant

controls (indicated by

SIA-Compliant Controls

in reverse type and heavy borders for easy identification).

Entry of a number other than one specified will give unpredictable results. Values shown in brackets are factory defaults.

SIA Guidelines for Non-SIA-Compliant Controls: Notes in certain fields give instructions for programming the FA168CPS/FA148CP for False

Alarm Reduction (these controls can be programmed to reduce false alarms, but they are not fully SIA compliant).

Field Function Data Entries Programmable Values

SYSTEM SETUP (

✱

20–

✱

29)

✱

20 INSTALLER CODE

| | | [4112]

4 digits, 0–9

✱

21 QUICK ARM ENABLE

[0,0]

Part. 1 Part.2

0 = no; 1 = yes

✱

22 RF JAM OPTION

[0]

0 = no RF Jam detection; 1 = send RF Jam report

UL: must be 1 if wireless devices are used

✱

23 QUICK (FORCED) BYPASS

[0,0]

Part. 1 Part. 2

0 = no quick bypass UL: must be “0”

1 = allow quick bypass (code + [6] + [#] )

✱

24 RF HOUSE ID CODE

| | |

Part. 1 Part. 2 Common

00 = disable all wireless keypad usage [00,00,00]

01–31 = using 5827, 5827BD or 5804BD keypad

✱

26 CHIME BY ZONE

[0]

0 = no; 1 = yes (select zones to chime on zone list 3,

using *81 Menu mode)

✱

POWERLINE CARRIER DEVICE (X–10)

HOUSE CODE

[0]

0 = A; 1 = B, 2 = C, 3 = D, 4 = E, 5 = F, 6 = G,

7 = H, 8 = I, 9 = J, #10 = K, #11 = L, #12 = M, #13 = N,

#14 = O, #15 = P UL: not for fire or UL installations

✱

28 ACCESS CODE FOR

PHONE MODULE

| [00]

(Partition 1 only)

00 = disable; 1st digit: enter 1–9; 2nd digit: enter # + 11

for "

✱

", or # + 12 for "#".

UL: must be “00” for UL Commercial Burg. installations

✱

29 LONG RANGE RADIO OUTPUT

[0]

0 = disable; 1 = enable

✱

31 SINGLE ALARM SOUNDING per ZONE

[0]

0 = unlimited sounding; 1 = one alarm sounding per zone

SIA-Compliant Controls: If “0,” “alarm sounding per zone” will be

the same as the “number of reports in armed period” set in field

*93 (1 if 1 report, 2 if 2 reports, unlimited for zones in zone list 7).

✱

32 FIRE ALARM SOUNDER TIMEOUT

[0]

0 = sounder stops at timeout;

1 = no sounder timeout UL: must be “1” for fire install.

✱

33 ALARM SOUNDER (BELL) TIMEOUT

[1]

0 = none; 1 = 4 min; 2 = 8 min; 3 =12 min; 4 = 16 min;

UL: For residential fire alarm installation, must be set for a

minimum of 4 min (option 1); for UL Commercial Burglary

installations, must be minimum 16 min (option 4)

✱

34 EXIT DELAY

UL: see inst. instr. for requirements.

| | [60,60]

Part. 1 Part. 2

Common zones use same

delay as partition 1.

00 - 96 = 0 - 96 secs; 97 = 120 secs

SIA Guidelines: minimum exit delay is 45 seconds

SIA-Compliant Controls: 45 - 96 = 45 - 96 secs; 97 = 120 secs

NOTE: Entries less than 45 will result in a 45-second delay.

✱

35 ENTRY DELAY #1 (zone type 01)

For UL Residential Burglary Alarm installations, must be

set for a maximum of 30 seconds; entry delay plus dial

delay should not exceed 1 min. For UL Commercial

Burglar Alarm, total entry delay may not exceed 45 secs.

| | [30,30]

Part. 1 Part. 2

Common zones use same

delay as partition 1.

00 - 96 = 0 - 96 seconds; 97 = 120 secs; 98 = 180 secs;

99 = 240 secs (

SIA Guidelines: minimum entry delay is 30 secs)

SIA-Compliant Controls: 30-96 = 30 - 96 secs; 97 = 120 secs;

98 = 180 secs; 99 = 240 secs

NOTE: Entries less than 30 will result in a 30-second delay.

✱

36 ENTRY DELAY #2 (zone type 02)

| | [30,30]

Part. 1 Part. 2

See *35 Entry Delay 1 above for entries.

∗

∗∗

∗37 AUDIBLE EXIT WARNING

[1,1]

0 = no; 1 = yes SIA Guidelines: must be enabled

SIA-Compliant Controls: Feature always enabled; field removed.

✱

38 CONFIRMATION OF ARMING DING

[0,0]

Part. 1 Part. 2

0 = no; 1 = yes (wired keypads and RF); 2 = yes, RF only

UL: must be “1” for UL Commercial Burglar Alarm inst.

✱

39 POWER UP IN PREVIOUS STATE

[1]

0 = no; 1 = yes UL: must be “1” SIA Guidelines: must be “1”

SIA-Compliant Controls: Feature must be enabled (enter 1).

DIALER PROGRAMMING (

✱

40 –

✱

42) Do not fill unused spaces. Enter 0–9; #+11 for '

✱

'; #+12 for '#'; #+13 for a 2-second pause. If

fewer than the maximum digits entered, exit the field by pressing [∗]. The next data field number is displayed.

✱

40 PABX ACCESS CODE or

CALL WAITING DISABLE

NOTES: 1.

The call waiting disable feature

cannot be used on a PABX line.

2. Using Call Waiting Disable on a non-call

waiting line will prevent successful

communication to the central station.

| | | | | Enter up to 6 digits. To clear entries, press ✱40✱. If call waiting

used, enter call waiting disable digits “∗ (#+11) 70” plus “# + 13” (pause).

SIA-Compliant Controls: If call waiting is used, enter call waiting disable digits as described

above, and also set Call Waiting Disable option in field *91.

1 2 3 4 5 6 7 8 ... 15 16

Commentaires sur ces manuels

Pas de commentaire

Ads Security FA700KP-ADS Guide d'installation Page 3

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Ads Security FA700KP-ADS